New RallyCam2000 / 3000 / 4000 Quick Start
If you have the old battery powered RallyCam System Click Here
1. Plug camera cables and audio cable into back of water-tight box. Plug 12volt accessory plug into vehicle’s accessory plug outlet, and into back of box.
2. Insert SD Cards into top and side (under battery cover) of DVR (writing down).
3. Press and hold the power button on the DVR until screen comes on.
4. Set DVR in box. Insert side of DVR firmly into plugs.
5. Navigate to “Movie Recorder” by using the toggle on the face of the DVR.
6. Press the toggle directly center to select the “Movie Recorder”.
7. Turn switch in box to “on”.
8. Press the record button (with a red dot) on top edge of DVR, or the red record button on the DVR remote. (red light will appear on screen)
9. When finished recording, press the record button (with a red dot) on top edge of DVR, or the red record button on DVR remote (red light will disappear, and yellow square will appear)
10. Turn switch in box to “off”.
11. To turn off, press and hold the power button until screen turns black.
* Use the row of buttons in the box, or the video processor remote to change camera views.
* make sure camera views are positioned correctly by looking at screen of DVR.
* make sure to insert an SD card into the DVR for your video to record onto.
If the DVR will not turn on:
a. open side of DVR and remove the battery.
b. slide battery back into side of DVR, and replace cover.
If Camera(s) will not power on:
a. recharge the box for at least 2 hours.
b. to turn camera(s) on, press the "on" switch downward.
c. to turn camera(s) off, press the "off" switch downward.
d. be sure to turn switch off after every recording session in order to save battery power.
If picture on video appears fuzzy, or has interference:
a. make sure DVR is plugged fully into the box.
b. make sure you have slid DVR gently left when removing from box, and not tugged upward on the DVR while still plugged into box.
c. make sure camera(s) are screwed fully into back of box.
d. if problem persists please contact customer service at: 425-741-2526, Country Code: 001, or email: info@edgecameras.com.
1. Plug camera cables and audio cable into back of water-tight box. Plug 12volt accessory plug into vehicle’s accessory plug outlet, and into back of box.
2. Insert SD Cards into top and side (under battery cover) of DVR (writing down).
3. Press and hold the power button on the DVR until screen comes on.
4. Set DVR in box. Insert side of DVR firmly into plugs.
5. Navigate to “Movie Recorder” by using the toggle on the face of the DVR.
6. Press the toggle directly center to select the “Movie Recorder”.
7. Turn switch in box to “on”.
8. Press the record button (with a red dot) on top edge of DVR, or the red record button on the DVR remote. (red light will appear on screen)
9. When finished recording, press the record button (with a red dot) on top edge of DVR, or the red record button on DVR remote (red light will disappear, and yellow square will appear)
10. Turn switch in box to “off”.
11. To turn off, press and hold the power button until screen turns black.
* Use the row of buttons in the box, or the video processor remote to change camera views.
* make sure camera views are positioned correctly by looking at screen of DVR.
* make sure to insert an SD card into the DVR for your video to record onto.
Record for Approximatey 30 Hours
Quad Processor Instructions
DVR Instructions
Troubleshooting:
If the DVR will not turn on:
a. open side of DVR and remove the battery.
b. slide battery back into side of DVR, and replace cover.
If Camera(s) will not power on:
a. recharge the box for at least 2 hours.
b. to turn camera(s) on, press the "on" switch downward.
c. to turn camera(s) off, press the "off" switch downward.
d. be sure to turn switch off after every recording session in order to save battery power.
If picture on video appears fuzzy, or has interference:
a. make sure DVR is plugged fully into the box.
b. make sure you have slid DVR gently left when removing from box, and not tugged upward on the DVR while still plugged into box.
c. make sure camera(s) are screwed fully into back of box.
d. if problem persists please contact customer service at: 425-741-2526, Country Code: 001, or email: info@edgecameras.com.
